Timber sealing in Australia commonly costs between $300 and $2,500 for a deck, or roughly $35 to $70 per square metre for sanding and sealing, according to current cost guides. A heritage façade is a different job. The sealer is a small part of the bill. Most of the cost sits in preparation, repairs and moisture detailing. This guide sets out the benchmark figures, explains what moves a quote, and shows how to compare Melbourne quotes properly.

Com
Protect Timber on Period Homes
Sol Shine provides timber sealing and restoration for Victorian and Edwardian homes across Melbourne’s inner east, bayside and surrounding suburbs.

Explore Sol Shine’s services

TL;DR

  • Professional deck resealing typically falls between $300 and $2,500, depending on deck size and condition.
  • Trade guides put deck sanding and sealing at about $35 to $70 per m², with capital cities often 10 to 20% higher than regional areas.
  • On Victorian and Edwardian homes, preparation, end-grain protection and rot repair cost more than the sealer itself.
  • Ask for a quote that splits cleaning, stripping, repairs, coating system, coats and access. A low quote that omits these is not comparable.
  • Sealing never fixes water entry. If timber is rotten or a joint leaks, repair comes first.

Table of Contents

What timber sealing actually means

“Sealer” is a loose word. WoodSolutions separates water-repellent preservatives, stains, paints, primers and undercoats, and each does a different job. The right one depends on the look you want, how exposed the timber is, and what is already on it.

For a deck, that might be an oil or stain. For a weatherboard façade, it is usually a primer and undercoat system with paint on top. For a window sill or a fretwork bracket, it is often a preservative treatment followed by a paint system. If you want the background first, our guide to what timber sealing is and why it matters covers it, as does our note on why seal timber surfaces.

Typical timber sealing prices in Australia in 2026

The figures below are guide prices from Australian cost publishers. They are not a fixed Melbourne tariff, and they assume a reasonably sound surface.

Job Typical guide price Source
Small deck, stain and reseal $300 to $450 hipages
Average deck $700 to $1,000 hipages
Large deck $1,300 to $2,500 hipages
Deck sanding and sealing, national About $35 to $70 per m² TradeRefer
Painting or sealing a timber house exterior, labour $35 to $60 per hour hipages

The TradeRefer guide also cautions that capital-city pricing may run 10 to 20% above regional areas. Treat that as a reason to expect Melbourne quotes toward the top of any range, not as a Melbourne price list.

Product cost is the small number

Retail sealers and oils sit in the tens to low hundreds of dollars per container. Whatever you read on a hardware page, the product is rarely what makes a professional quote large. Labour, access, preparation and repairs do.

What drives the price up

Hipages notes that labour and scope vary with the number of coats, staining, mould or dirt, timber replacement, sanding and nail punching. For decks and heritage exteriors, these are the drivers we see matter most.

  1. Existing coating condition. Sound coatings need cleaning and a light key. Failed coatings must be stripped back, which takes far longer.
  2. Rot and damaged boards. Soft timber needs repair or replacement before any finish goes on.
  3. Height and access. Double-storey façades, gables and high eaves need scaffolding or lifts.
  4. Number of coats and system type. A primer, undercoat and two topcoats cost more than a single oil coat, and last differently.
  5. Detail density. Fretwork, brackets, sills, fascias, window frames and corner boards all take hand work.
  6. Waste removal and site protection. Often missing from the cheapest quotes.

Why heritage timber costs more than a standard deck

On a Victorian or Edwardian home, the question is not “what is the cost per metre?” It is which moisture pathways and timber defects are being corrected before the finish goes on. WoodSolutions’ durability guidance says failures most often involve moisture held against timber, water getting in at joints or end grain, trapped vapour, or contact with wet masonry.

End grain needs its own allowance

WoodSolutions states that end grain absorbs water up to 10 times faster than face grain, so it must be sealed, flashed or protected by detailing. On a period home, that means cut board ends, window sills, decorative trims and any freshly cut replacement pieces. A good scope lists these separately.

Weatherboards

For external cladding, WoodSolutions recommends sealing the entire board according to the specified finish, priming or undercoating all surfaces where paint is intended, and giving freshly cut surfaces extra water-repellent treatment. It also warns that moisture entering end grain can contribute to peeling and rot beneath the coating.

If your boards are failing rather than just tired, read our guide to heritage weatherboard rot repair in Melbourne and the weatherboard replacement guide.

Sealing is not a substitute for repair

Coating over a leaking joint or rotten timber hides the defect and shortens the life of the restoration. Sloped surfaces, drip edges, flashing, drainage gaps and ventilation keep timber dry, and a sealant system works best when those details are sound. This is why a heritage job can move well beyond deck-style pricing, and why we cover the wider picture in our Melbourne timber restoration price guide.

Decks: new timber, old timber, or composite

For new or replacement decking, WoodSolutions recommends applying a water-repellent preservative or oil-based primer, then the intended finish, to joists and all decking surfaces before fixing where practicable, and sealing freshly sawn ends immediately. Unfinished external decking fades silver-grey and may distort, split and develop surface checking. Sealing the whole component, not just the top face, is cheaper than fixing cupping later. A decking planning and preparation guide makes the same point about timber condition driving both cost and durability.

Deck boards treated before they are fixed

Is composite cheaper than timber?

Upfront, usually not. Ekodeck’s own comparison tool describes the general trade-off: timber is usually cheaper at the start but needs ongoing sanding, oiling and sealing, while composite costs more initially and may need less maintenance. Its result depends on the assumptions you enter. Price data checked to 8 October 2026 lists composite and PVC boards at $63 to $426 per m² including GST, with a middle price of $156 per m². Those are board prices, not an installed deck.

For a period home, authentic timber appearance and repairability often matter as much as the maintenance calendar, so the cheapest lifecycle figure is not always the right answer.

Is composite cheaper than timber? — overview diagram

How to compare timber sealing quotes

The TradeRefer guide suggests collecting two to three written quotes and confirming what each includes. We would go further. Ask every contractor to itemise:

  • Cleaning and mould or dirt removal
  • Sanding or stripping of failed coatings
  • Timber repairs and replacement, priced per item or per metre
  • End-grain and cut-end treatment
  • The named coating system: primer, undercoat, finish and number of coats
  • Scaffolding or access equipment
  • Waste removal and GST

Hipages makes the same recommendation: split the quote rather than accept a single per-square-metre figure.

Check compatibility and recoat windows

Not every product layers over another. According to WoodSolutions, some water-repellent preservatives are incompatible with pigmented stains, LOSP-treated timber can affect adhesion, and a water-repellent preservative may need about two weeks before a subsequent finish. A professional quote should identify the existing coating, the proposed system, the compatibility checks and the recoat window. If it does not, ask.

Our 10 point quote checklist for timber window restoration applies the same discipline to windows, and common exterior painting mistakes shows where cheap preparation fails.

Our perspective

We are painters first, and most of our heritage work starts with a homeowner who has been told the timber just needs sealing. Sometimes that is true. More often, once we inspect, there is an open joint, a soft sill, or a coating that will not hold a new system. Sealing over those problems costs less on the day and more within a few years.

That is why we manage preparation, repairs, carpentry and painting in-house under a single project lead. The person who finds the defect is accountable for fixing it and for the finish that goes over it. You are not coordinating a carpenter, a painter and a render specialist who each assume the other has covered the end grain.

Our advice on price is simple. Be wary of a quote that is far lower than the others without a clear scope. Ask what the coating system is and what was done about moisture. Heritage timber rewards the quote that explains itself.

— Jarrad

Working with Sol Shine

We take on large-scale heritage painting and restoration projects across Melbourne’s inner east, bayside and inner north, including Kew, Hawthorn, Camberwell, Brighton, Malvern, Richmond, Fitzroy and Northcote. If your timber needs more than a weekend recoat, see our heritage painting services or our exterior painting page, then get in touch for an inspection and a scoped quote. We do not publish fixed prices, because every period home carries different repairs.

FAQ

How much does it cost to seal a timber deck in Australia?

Guide prices run from about $300 to $450 for a small deck up to $1,300 to $2,500 for a large one, per hipages. Per square metre, sanding and sealing is around $35 to $70 nationally. Expect the higher end in Melbourne if repairs or heavy sanding are involved.

What can you use to seal timber?

That depends on the timber and the finish you want. WoodSolutions distinguishes between water-repellent preservatives, stains, paints, primers and undercoats, and says the choice should follow the appearance, exposure and compatibility with any later coating. Always confirm compatibility before layering products.

Is Ekodeck cheaper than timber?

Not upfront. Ekodeck’s comparison tool states that timber is usually cheaper initially but needs ongoing sanding, oiling and sealing, while composite may need less maintenance. Which is cheaper over time depends on the products, labour and maintenance you assume.

Does sealing stop weatherboards rotting?

It helps only when the timber is sound and water entry is controlled. WoodSolutions warns that moisture through end grain can cause peeling and rot beneath finishing coats. Sealing over leaking joints or rotten timber can hide the problem, so repair comes first.

Sources

Meet the Author

info@solshine.com.au