Most isolated glazing putty failures are a manageable DIY job: remove the loose putty, bed the glass, fix new glazing points, run fresh linseed oil putty, tool it to a weather-shedding profile, then paint. Extensive rot, structural sash problems or fragile heritage glass are different matters, and those call for a professional with restoration experience.
TL;DR:
- Inspect putty every 6 to 12 months; isolated cracked sections can be patched, but soft timber or failures across several panes need broader repair.
- For windows painted before the 1970s, use wet cleanup, gloves, eye protection, and a P2 respirator; avoid dry scraping or sanding.
- Seal the rebate with shellac or diluted oil primer before glazing, space glazing points 150 to 200 mm apart, and tool a 45 degree bevel.
- Let the putty form a skin for a few days, then paint after 2 to 4 weeks, overlapping the glass by 1 to 2 mm.
- Bring in a restoration specialist for heritage windows with fragile original glass, suspected lead paint, structural sash problems, or unsafe upper story access.
Table of Contents
- Tools and materials you need for glazing putty repair
- Inspection and preparation: assess the window and plan the repair
- Remove old putty cleanly and safely
- Bedding the glass and applying new putty (practical steps)
- Tooling, finishing and painting the putty for long life
- Common problems and quick troubleshooting fixes
- Heritage and safety considerations: why some jobs need a specialist
- A heritage restoration painter’s view on putty repairs
- How we can help with heritage window restoration
- FAQ
- Sources
Tools and materials you need for glazing putty repair
A tidy glazing repair starts with the right kit laid out before you touch the window. You will need a sharp putty knife, a hacking knife or old chisel for stubborn sections, pliers for lifting old glazing points, and a wire brush for cleaning the rebate. An infrared speed heater is a useful optional extra for softening aged putty without scorching the timber.
Personal protection matters more than most DIYers expect, particularly on windows painted before the 1970s. Gloves, eye protection and a P2 respirator are worth having on hand, along with a damp-wipe routine rather than dry sanding, to keep old paint dust out of the air.
Traditional linseed oil putty is the standard choice for timber sashes because it stays flexible, bonds well to oil-based paint and can be tooled to a fine edge. Selleys Special Putty is a widely available Australian linseed oil based glazing putty made for timber frame windows, and its product directions are a useful reference point for timing and inspection. Acrylic or modern sash glazing compounds exist, but linseed putty remains the preferred option for painted timber because it bonds reliably with linseed oil paint.
Keep these consumables nearby:
- Glazing points (also called sprigs) in a few sizes
- Shellac or a diluted oil primer for sealing the timber rebate
- Methylated spirits for cleaning tools and glass
- Chalk and whiting to firm putty in warm conditions
- Fine sanding pads for smoothing the rebate before priming
Inspection and preparation: assess the window and plan the repair
Before picking up a putty knife, work out whether you are dealing with a simple patch or a full reglaze. Run through this checklist on each affected pane:
- Press the putty with a thumbnail. Hard, cracked or crumbling sections need removal.
- Check for unpainted or peeling putty, which lets moisture in faster than sound, painted sections.
- Test the surrounding timber with an awl or screwdriver tip. Soft, spongy wood signals rot rather than a putty-only problem.
- Look for water staining, flaking paint or dark patches on the sill below the pane, all signs of ongoing ingress.
- Note how many panes are affected. One or two cracked sections is a weekend job. Multiple panes across a sash usually point to a bigger underlying issue.
Product guidance for linseed oil glazing putty recommends inspecting windows every 6 to 12 months, which gives you a simple maintenance rhythm rather than waiting for a crack to appear (Selleys Special Putty).
Once you have scoped the job, mask the surrounding glass and frame, lay a drop sheet to contain debris, and use wet methods rather than dry scraping if the existing paint predates the 1970s. Dry the rebate fully before any new putty goes in, since trapped moisture under fresh putty is a common cause of early failure.
Remove old putty cleanly and safely
Old, brittle putty needs to come out without cracking the glass or gouging the timber rebate underneath. Gentle infrared heat from a speed heater softens the putty enough to lift it in sections, and careful hand work with a hacking knife achieves the same result more slowly. Avoid aggressive chisel work or an open flame near glass, since both risk cracking the pane or scorching the timber.
Work through the pane systematically:
- Soften a small section, then lift it with the putty knife angled away from the glass
- Pull or cut out the old glazing points with pliers, working from the edges inward
- Support larger panes with wooden wedges or a helper’s hands before the last points come out
- Clear all putty residue and dust from the rebate with a wire brush
- Vacuum rather than sweep to limit dust spread, especially on older paint layers
Pro Tip: Work one pane at a time on multi-pane sashes so the remaining glazing keeps the sash square while you reglaze each section.
If the pane needs to come out entirely, support the glass fully before the last glazing point is removed. A dropped or twisted pane is the most common accident in this job, and older or leaded glass is particularly unforgiving.
Bedding the glass and applying new putty (practical steps)
A durable repair depends on how well the glass is bedded and supported before the front putty goes anywhere near a knife. Follow this sequence:
- Press a thin, even bed of putty into the clean rebate so the glass sits on a cushion rather than bare timber, which prevents rattling and uneven pressure on the pane.
- Position the pane into the bed and press it gently and evenly around the edges until it seats flush with the sight line.
- Insert glazing points by hand or with a push tool, spacing them roughly every 150 to 200 mm around the perimeter, with at least two points per side on smaller panes and more on larger ones to spread the load evenly.
- Roll a rope of putty between your palms and press it firmly around the glass edge, working it into the rebate so there are no air gaps behind it.
- Draw the putty knife along the bead at a consistent angle, forming a neat bevel that slopes away from the glass so rain sheds off rather than pooling against the frame.
Keep the putty workable as you go. If it feels stiff, kneading it between your hands with a touch of raw linseed oil restores workability, while a pinch of chalk firms it up again in warm conditions.
The bevel angle is what separates a cosmetic repair from a weather-tight one. Too flat, and water sits on the putty; too steep, and it will not hold its shape or bond properly to the rebate. Aim for a consistent 45 degree slope from the sight line down to the rebate edge, checking it against an unaffected pane nearby if one is still original.
Tooling, finishing and painting the putty for long life

Tooling is where a rough bead becomes a finished, weather-shedding profile. Run the putty knife along the bevel in one smooth pass where possible, cleaning the blade between strokes so you are not dragging debris back into the line. Trim any excess from the back of the glass so it sits flush with the inside face of the sash.
Sealing the rebate before glazing is one of the most effective steps you can take to stop a repair failing early. A thin coat of shellac or a diluted oil primer stops the timber drawing oil out of the fresh putty, which is the most common cause of shrinkage and cracking soon after a repair (correct puttying technique, CR Laurence; reglazing with linseed oil putty, Sydney Paint Warehouse).
- Seal the bare rebate with shellac or primer before bedding the glass, not after
- Let the putty skin over for a few days before handling it further
- Overlap the paint roughly 1 to 2 mm onto the glass itself, which locks out water at the most vulnerable edge
Putty cures from the outside in rather than all at once. Product guidance for Selleys Special Putty recommends painting between 2 and 4 weeks after glazing, which gives the surface time to skin while the paint still bonds properly (Selleys Special Putty). Separate trade guidance notes that putty can often be painted after around two weeks once a firm skin has formed, though full hardening can take closer to six weeks (correct puttying technique, CR Laurence). Either way, try to finish the job well before a stretch of heavy wet weather, since uncured putty is far more vulnerable to rain than a painted, cured bead.
Common problems and quick troubleshooting fixes
Most putty failures trace back to one of a handful of causes, and knowing which one you are looking at saves unnecessary work.
- Shrinking and cracking: usually a sign the rebate was never sealed, letting timber absorb oil from the putty; a repair should include a shellac seal this time around
- Hairline surface cracks with sound putty underneath: often fixable with a linseed oil slurry brushed into the old putty to rebind it, delaying a full reglaze when the pane itself is not loose
- Localised crumbling at one corner: typically a patch job: cut out the damaged section only, rather than stripping the whole pane
- Putty that has fully detached from the glass or frame: this needs full removal and reglazing rather than patching, since the bond has failed completely
- Soft or spongy timber beneath the putty: this points to rot rather than a putty problem, and no amount of reglazing will fix it on its own
When you are patching rather than reglazing, work the new putty firmly into the old material at the edges so there is no visible seam once painted.
Heritage and safety considerations: why some jobs need a specialist
Heritage-listed and period timber windows deserve a more cautious approach than a standard repair. Technical guidance for heritage timber doors and windows recommends doing as little as possible and matching original materials wherever practical, including retaining original glass where it can be saved rather than replacing it outright (Heritage Technical Note, Queensland Government). That principle guides how we approach every heritage sash we touch, from matching putty profiles to sourcing comparable glass rather than defaulting to new.
Lead paint is a real consideration on pre-1970s homes, and fragile early glass can crack under pressure that a modern pane would tolerate without issue. A few signs it is time to bring in a professional:
- Multiple panes failing across one sash, which often points to a wider structural or moisture problem
- Visible or suspected lead paint on window frames, which needs containment rather than dry sanding
- Original or historic glass that is cracked, bowed or difficult to source a match for
- Soft timber in the sash or frame, which needs proper timber repair work rather than putty alone
A heritage restoration painter’s view on putty repairs
The jobs that last are rarely the ones with the neatest bead. They are the ones where the rebate was sealed properly, the paint overlapped the glass by that extra millimetre or two, and nobody rushed the cure before painting. Preparation and sequencing make the difference between a repair that holds for a decade and one that cracks again within a year.
Competent DIYers can absolutely tackle an isolated cracked pane with the right technique. Where we add the most value is on heritage homes with multiple failing panes, early glass worth saving, or sashes that need structural attention alongside the glazing, because those jobs benefit from an integrated approach rather than piecemeal fixes.
— Jarrad
How we can help with heritage window restoration
Heritage window and timber restoration is often managed as part of a broader in-house service, so a damaged sash, rotted frame or failing putty line can be coordinated by the same project lead handling the painting work, rather than passed between separate trades. That matters most on period homes where matching the original profile and glass takes judgement, not just a new tube of putty.

It is worth booking a professional inspection when you are facing failure across several panes, suspected timber rot, lead paint on older frames, or access to upper storeys that makes DIY work genuinely risky. Our heritage painting services cover this kind of work alongside full exterior and interior repaints, and timber window and frame repairs sit within our broader restoration capability.
Get in touch through our contact page to arrange an inspection and a scope of works for your windows and the rest of your home’s exterior.
FAQ
How long does new glazing putty take to cure?
Linseed oil putty typically skins over within days and firms up enough to paint within 2 to 4 weeks, with full hardening taking longer. Product guidance for Selleys Special Putty recommends painting in that 2 to 4 week window rather than rushing it.
Can I patch glazing putty without removing the whole bead?
Yes, when the glass itself is not loose and the damage is limited to a small section, cutting out just the damaged putty and applying fresh material is a reasonable fix. A linseed oil slurry brushed into sound but cracked old putty can also rebind it and delay a full reglaze.
How often should I inspect window putty?
Manufacturer guidance recommends checking glazing putty every 6 to 12 months, looking for cracking, loss of paint cover or gaps at the glass edge. Catching small failures early avoids water getting into the timber rebate underneath.
Why does glazing putty crack and fail so often?
The most common cause is an unsealed timber rebate drawing linseed oil out of the fresh putty, which leads to shrinkage and cracking soon after glazing. Sealing the rebate with shellac or a thin, diluted oil primer before glazing addresses this directly.
When should I call a professional instead of doing it myself?
A professional is worth calling when several panes have failed at once, when there is soft or rotted timber in the sash, when lead paint is suspected, or when the window is part of a heritage property with original glass worth preserving. Our guide to rotted window frame repair covers the warning signs in more detail.
Sources
- Directory
- Reglazing timber windows with linseed oil putty — Sydney Paint Warehouse
- Heritage Technical Note – Minor repairs – timber doors and windows (Queensland Government)
- Correct puttying technique (CR Laurence Australia)




